Siding Contractor in Fairview, TX Built for Hail, Heat and Clay Soil

Impact damage from hail and high winds. It shows up as cracked or holed vinyl, dented aluminum, chipped or fractured fiber cement, and panels torn loose. Even small breaks open a path for wind-driven rain to reach the sheathing and framing behind your siding.

Collin County sits in Hail Alley, and spring storms from March through June regularly bring golf-ball-size hail or larger. The siding most exposed here is on gables, second-story walls and rear elevations, all of which face the storm directly. Straight-line winds often follow the hail, peeling back loosened panels. After big storms, out-of-town storm chasers flood Fairview and Allen, so many homeowners end up with rushed or incomplete repairs that leak the next season.

• Cracks, holes or splits in vinyl panels
• Round dents in aluminum siding or trim
• Chipped corners or fractured edges on fiber cement
• Panels missing or flapping after a storm
• Spatter marks or dents on the windward elevation
• Neighbors filing hail claims after the same storm

We see heavy damage on north- and west-facing gables in Heritage Ranch, Stonebridge Ranch and Twin Creeks after spring storms. Two-story homes with siding above brick tend to take the worst hits because the upper walls catch hail at full force.

We document the damage for your insurance adjuster, secure open areas, then replace damaged courses or whole elevations with matched or upgraded material and proper flashing.

Failure of the 1990s–2000s hardboard and composite siding, including Masonite and LP Inner-Seal–era products. When water gets in, the wood-fiber core swells, the edges mushroom and the board softens. Fresh paint often hides the damage until the board crumbles.

Thousands of Collin County homes built in the 1990s and early 2000s were sided with hardboard. Twenty-plus years of heavy rain, sprinkler overspray and freeze-thaw cycles have pushed water into cut edges and nail holes. The heat bakes the paint film until it cracks, which lets in more moisture. Low bottom courses next to landscape beds wick water constantly, so the damage usually starts at the drip edge and works its way up.

• Bulging or swollen board edges
• Soft spots that give when pressed
• Bottom courses flaking or crumbling
• Paint that won't stick or keeps peeling
• Visible nail heads sunk into the board
• Woodpecker holes in the siding

This is common in 1990s–2000s neighborhoods in Allen, Plano's Deerfield area, Murphy and Woodbridge in Sachse and Wylie. Homes near Lake Lavon and wooded lots in Lucas and Parker also see woodpecker damage to these softer boards.

We replace failed hardboard with James Hardie fiber cement or LP SmartSide, repair damaged sheathing, and install new house wrap and flashing.

Wood decay in the chimney chase siding, fascia boards, window and door trim, and sills. Trim sits at the joints where water collects, so it's usually the first part of the exterior to rot, often well before the siding does.

Wood chimney chases are standard on North Texas homes, and they rarely get the metal cap flashing and kick-out details they need. Heavy rain overruns the gutters and soaks the fascia. Texas sun dries out the caulk at window corners, so water gets in behind the trim. Freezes like Uri then expand trapped water and split the boards.

• Soft or crumbling wood at window corners
• Peeling paint on the fascia
• Dark stains below the chimney cap
• Gaps between trim and brick
• Ants or termite activity in the trim
• Gutters pulling away from the fascia

Chimney chases on two-story homes in Craig Ranch, Star Creek and Willow Bend are frequent repair calls. Window sills on west-facing walls throughout Fairview and Plano rot faster because of heat-cracked caulk.

We remove rotted wood, repair the substrate, add proper flashing and chase caps, and install fiber cement or PVC trim so it doesn't come back.

Siding seams, butt joints and trim joints that open up when the house shifts. Expansive clay under the slab moves the structure, which pulls the siding apart, splits caulk and lifts trim away from windows and brick.

Fairview sits on Blackland Prairie clay that swells after heavy rain and shrinks hard during dry summers. That seasonal movement racks the framing. Rigid caulk can't keep up, and siding fastened too tight has no room to move. Partial-wall siding over brick is especially vulnerable, because brick and siding move at different rates.

• Open butt joints between planks
• Cracked caulk lines at windows and corners
• Gaps where siding meets brick
• Stair-step cracks in nearby mortar
• Doors or windows that stick seasonally
• Trim pulling away from the wall

We see this most after long dry summers, on homes in Parker, Lucas and older parts of Plano and Richardson. Larger custom homes with long, uninterrupted walls in Fairview show it at their corner and window joints.

We re-fasten or replace affected boards with correct expansion gaps, use flexible sealants and flash the brick-to-siding transition. If movement looks severe, we'll recommend a foundation assessment.

Wavy, rippled or buckled vinyl panels caused by heat. Lower-grade vinyl softens in extreme temperatures, and reflected sunlight from neighboring Low-E windows can concentrate enough heat to melt or distort it.

North Texas summers routinely hit the upper 90s, and 100°F+ days are common. Lighter-gauge vinyl on south- and west-facing walls expands past what it can handle, especially if the installer nailed it too tight. In dense subdivisions, Low-E glass on the house next door can reflect concentrated sunlight onto your walls.

• Wavy or rippled panels
• Panels sagging or pulling from the lock
• Melted or distorted spots
• Panels that buckle in afternoon heat
• Fading on sunny elevations

This is common on starter homes and older vinyl-sided houses in Garland, Wylie, Sachse and Princeton, especially on closely spaced lots where neighboring windows face your siding.

We replace distorted panels with heavier, heat-tolerant vinyl installed loosely enough to expand, or upgrade those elevations to fiber cement.

Paint failure on fiber cement siding. The finish turns chalky, fades unevenly or peels. Fiber cement itself is durable, but its paint is the first line of defense and wears out under constant UV exposure.

After about 10–15 years of Texas sun, field-painted fiber cement starts to chalk and fade, especially in darker colors. Once the paint breaks down, moisture can get into cut ends and butt joints. Many HOAs also require color consistency, so a faded elevation can lead to a compliance letter.

• Chalky residue that rubs off on your hand
• Uneven color between sunny and shaded walls
• Peeling at butt joints
• Exposed cut ends at corners
• An HOA notice about exterior maintenance

This is typical in 2000s-era neighborhoods in Stonebridge Ranch, Starwood and Twin Creeks, where original fiber cement is now hitting its repaint-or-replace window.

We repair joints, recaulk and repaint, or replace worn elevations with factory-finished James Hardie ColorPlus for longer-lasting color.

Water getting behind the siding where it meets brick, roof lines or windows because flashing is missing or done wrong. You usually can't see it from outside until the sheathing rots or stains show up inside.

Most local homes combine brick and siding, and every place they meet needs a proper flashing detail. Builders often skipped kick-out flashing at roof-wall intersections and relied on caulk alone. With 38–42 inches of rain a year falling in heavy bursts, those weak spots take on a lot of water.

• Stains on interior walls or ceilings
• Rot at the bottom of a roof-wall intersection
• Bubbling paint above brick ledges
• Musty odors in upper rooms
• Missing kick-out flashing at the roof line

This is common on two-story homes with complex rooflines in Craig Ranch, Windsong Ranch and Heritage Ranch, and on partial-wall siding above brick throughout Allen and Frisco.

We open the affected area, replace rotted sheathing, and install house wrap, kick-out and transition flashing before putting the siding back on.